<track id="r0j4x"><strike id="r0j4x"></strike></track>
    1. 首頁 > 技術交流

      技術交流

      電子槍的應用、原理、安裝配置和訂購信息

      Thermionics e-Gun?, an electron beam eva-poration source, is used to produce uniform high-purity films and optical coatings. The compact design and ease of maintenance make it useful in practically all vacuum systems and for many varied applications. It has been used to evaporate refractory and dielectric materials, as well as the more common conductive and semiconductor materials. e-Gun evaporation sources are reliable and simple to operate. They are equally suited for research or production applications.?
      ?
      Custom Installation: Twin HM2 e-guns
      Mounted on a Single Flange-Inside View Theory of Operation
      Electron beam heating is an efficient way of achieving temperatures in excess of 3500°C (6300°F) for uniform thin film, optical coating and vacuum metallurgic processes. The all-metal-sealed models are bakeable to 230°C (446°F). The e-Gun source and companion control power supply have been designed to be part of any high or ultra-high vacuum system.

      The e-Gun source is a self-accelerated electron beam device. A beam of electrons, held at a high negative potential, is produced by the hot tungsten filament. The beam of electrons leaving the filament is magnetically focused and then deflected 270° by the integral permanent magnet. The electron beam is accelerated into the evaporant material contained within the water-cooled, grounded crucible. The beam strikes the evaporant material with a spot of approximately 1/8” diameter and an intensity of approximately 25 kW/cm2. Sweeping the electron beam across the evaporant material contained in the crucible is performed by an electro-magnetic system, with either manual or automatic controls.
      ???
      The rate at which source materials may be evaporated is dependent upon power input, charge size, charge shape, and the characteristics of the material to be evaporated. The highest evaporation rates are obtained with materials that have low evaporation temperatures and low thermal conductivity.
      ???
      The evaporant vapor cannot become contaminated because the focused electron beam strikes only the evaporant source material in the crucible. The beam deflection and effective shielding keeps the filament hidden from the evaporant vapor. The crucible is cooled so efficiently that its surface never gets warm enough to react with the evaporant material.

      The e-Gun source will operate in a system base pressure as low as 5 x 10-11 Torr. The magnitude of pressure, which normally increases during evaporation, depends on the pumping capacity of the system and the cleanliness of the evaporant material. This pressure increase is minimized by the high thermal efficiency of the source. There is minimal outgassing of surrounding surfaces because only the evaporant is heated.??
      Outside View?
      ???
      All of the single, linear motion, three and five position e-Guns are 100% metal-sealed, thus eliminating “O” ring outgassing. Outgassing could require additional pumping capacity and sometimes result in sample contamination.

      Mounting Configurations

      Each e-Gun is available in three standard mounting configurations:
      1.e-Gun mounted on a PyraFlat or ConFlat metal-seal type flange, which uses a standard OFE copper gasket
      2.e-Gun with a 1” diameter bolt-type mount, which mount through a 1” diameter hole, and is sealed by a compression O-ring
      3.e-Gun alone with no mounting flange
      4.Ordering Information
      Ordering Information
      Please specify the mounting configuration at the time the order is placed, the prices listed may not include the bolt-type or flange-type mount.
      Other mounting flanges, configurations and geometries are routinely supplied, please call the factory for further information.

      Custom e-Guns
      Any e-Gun can be designed and manufactured to fit existing or new systems. Please consult the factory with your special requirements.

      電子槍,也叫電子束蒸發源,是用來研制生產高純度均勻薄膜和光學涂層。緊湊的設計和易于維護,使其在幾乎所有的真空系統和許多不同的應用程序有用。它已被用于蒸發,耐火材料和電介質材料,以及更常見的導電和半導體材料。電子槍蒸發源可靠,操作簡單。適用于研究或生產應用。
      ??
      自定義安裝:雙HM2電子槍
      裝在一個單法蘭內查看操作理論
      電子束加熱是一種可以實現溫度超過3500℃(6300 ° F)來制作均勻薄膜有效的方式,光學鍍膜,真空冶金過程。全金屬密封的車型烘烤至230 ° C(446 ° F)。電子束蒸發源及其控制電源已被應用在任何高真空或超高真空系統中。

      電子槍的是一個自我加速的電子束裝置。電子束是由熱鎢絲在負高壓作用下形成。離開燈絲的電子束被磁聚焦并在永久磁鐵作用下偏轉270 °。電子束以約25 kW/cm2的強度打到坩堝內大約1/8"直徑的蒸發材料上,坩堝帶有水冷,接地。掃描整個坩堝中的蒸發材料的電子束由一個電磁系統完成,可手動或自動控制。
      ????
      材料蒸發的速率取決于輸入功率,電荷大小,電荷的狀態以及要蒸發的材料的特性。蒸發溫度低,導熱系數低的材料,獲得最高的蒸發率。
      ????
      蒸發材料的蒸氣不會造成污染,因為聚焦后的電子束只會打在坩堝內的蒸發材料商。電子束偏移及有效的保護可以使燈絲隱藏起來免受蒸氣污染。坩堝得到有效冷卻,使其表面無法達到足夠溫度與蒸發物質發生反應。

      電子槍在一個壓力為5 × 10-11托的環境下運行。通常在蒸發過程中氣壓會上升,這取決于泵的抽速和蒸發材料的清潔度。氣壓的升高隨著蒸發源的高效被最小化。表面只有最少量的出氣,因為只有蒸發劑被加熱。
      外觀????
      所有的單一,直線運動,電子槍各個位置是100%的金屬密封,從而消除了“O”型圈出氣。出氣可能會消耗泵的部分功率,并且會導致樣品污染。

      安裝配置

      每個電子槍都有三種標準安裝配置:
      1.電子槍安裝在一個PyraFlat或ConFlat金屬密封的法蘭上,它采用標準無氧銅墊片。
      2.電子槍帶有一個直徑1“螺栓,安裝時穿過1”直徑的孔,并通過壓縮O形圈密封
      3.電子槍槍沒有安裝法蘭
      4.Ordering信息
      訂購信息
      訂購時請指定安裝配置

      自定義電子槍
      任何電子槍可以設計和制造,以適應現有的或新的系統。根據您的特殊要求,請咨詢我們。

      国产女主播喷出白浆视频